Frequently Asked Questions

The MLTSS assessment and care planning measures include:

• LTSS Comprehensive Assessment and Update
• LTSS Comprehensive Care Plan and Update
• LTSS Shared Care Plan with Primary Care Practitioner(PCP)
• LTSS Reassessment/Care Plan Update after Inpatient Discharge
• Screening, Risk Assessment, and Plan of Care to Prevent Future Falls: Falls Part 1 (Screening) and Falls Part 2 (Risk Assessment and Plan of Care)

FAQ ID:89066

It is recommended that MLTSS plans report both rates. However, if the state believes there are valid reasons for not reporting both rates, such as costly changes in assessment and care planning forms and information technology systems, it might consider phasing in the supplemental rates over time. For instance, in the first year of measure use (for example, measurement year 2018), the state could require MLTSS plans to report just the core rate, and then require that MLTSS plans report both core and supplemental rates for measurement year 2019 or 2020. Although they are called "supplemental rates," they are still very important, and should be viewed as "aspirational." MLTSS plans should strive to cover more assessment and care plan elements over time.

FAQ ID:89071

Value sets are the complete set of procedure and diagnostic codes used to identify a service or condition included in a measure. One of the assessment and care planning measures—LTSS Reassessment/Care Plan Update after Inpatient Discharge—uses value sets to identify potentially planned hospitalizations. Please see "Do I need to use value sets to calculate these measures? If so, where can I find the value sets?" for more information regarding using value sets for the three institutional rebalancing and utilization measures.

View the value sets (XLSX, 2.88 MB). Please see Table 2 in the "LTSS Value Sets to Codes" tab. Table 1 in the "LTSS Measures to Value Sets" tab shows each value set needed for each measure.

FAQ ID:89076

Yes, the same sample can be used for Part 1 of the Screening, Risk Assessment, and Plan of Care to Prevent Future Falls measure as the LTSS Comprehensive Assessment and Update, LTSS Comprehensive Care Plan and Update, and LTSS Shared Care Plan with Primary Care Practitioner measures.

FAQ ID:89081

In accordance with Medicare cost reporting, the state must use 12 months of cost data reported by each facility. With regard to payment data, the state should use actual amounts, to the extent available, then calculate a claims completion factor based on historic utilization. The state’s UPL submission must include an explanation of its methodology to estimate payments. The use of a claims completion factor provides a reasonable estimate of the amount that Medicare would pay for these services, consistent with the UPL as defined at 42 CFR 447.272.

FAQ ID:92446

Effective state fiscal year 2020, each state must submit a complete data set of payments to Medicaid providers, including providers paid at cost, as well as critical access hospitals. This would require states to submit cost and payment data to CMS that previously was not requested.

FAQ ID:92456

The Centers for Medicare & Medicaid Services expects states receiving Federal Financial Participation to share with other states project artifacts, documents and other related materials, and systems components and code for leverage and reuse.

Read the state Medicaid director letter (SMD #18-005) on reuse (PDF, 70.77 KB). Reuse can be accomplished through sharing or acquiring:

• An entire set of business services or systems, including shared hosting of a system or shared acquisition and management of a turnkey service
• A complete business service or a stand-alone system module
• Subcomponents such as code segments, rule bases, configurations, customizations, and other parts of a system or module that are designed for reuse

FAQ ID:93631

To get started with reuse, a state can:

• Review the state Medicaid director letter (SMD #18-005) on reuse (PDF, 70.77 KB)
• View the introductory video  to get familiar with the concept and framework of reuse
• Contact the Medicaid Enterprise Systems (MES) at MES@cms.hhs.gov to request access to the MES Reuse Repository

FAQ ID:93636

The Centers for Medicare & Medicaid Services (CMS) established the Medicaid Enterprise Systems (MES) Reuse Repository to support states’ ability to share and reuse project life cycle artifacts. The repository is available on the CMS zONE (Opportunity to Network and Engage). States must have a CMS Enterprise Identity Management login to access the Reuse Repository.

View complete instructions for accessing the Reuse Repository.

Contact MES at MES@cms.hhs.gov for additional assistance in accessing the repository.

FAQ ID:93641

The reuse webpage on Medicaid.gov features an introductory video and more information about reuse. The webpage also has policy guidance documents.

The Medicaid Enterprise Systems Reuse Repository has instructions on how to use its features. These include how to add artifacts, search for artifacts, use the discussion forum features, and more.

FAQ ID:93646