Frequently Asked Questions

The measures are intended for any MLTSS plan that covers Medicaid LTSS benefits. Federal regulations pertaining to 1915(c) waivers require person-centered service plans,¹ but states can decide whether to require MLTSS plans participating in a state program operating under 1915(c) authority report these measures, and if they do, states can specify which types of plans and eligible members to which the measures apply.

¹"In accordance with 42 CFR §441.301 (b)(1)(i), all waiver services must be furnished pursuant to a written service plan that is developed for each waiver participant." (1915c waiver application, Instructions, Technical Guide and Review Criteria (PDF, 2.29 MB), Appendix D-1: Service Plan Development, CMCS, DEHPG, November 2014.

FAQ ID:89061

The MLTSS assessment and care planning measures include:

• LTSS Comprehensive Assessment and Update
• LTSS Comprehensive Care Plan and Update
• LTSS Shared Care Plan with Primary Care Practitioner(PCP)
• LTSS Reassessment/Care Plan Update after Inpatient Discharge
• Screening, Risk Assessment, and Plan of Care to Prevent Future Falls: Falls Part 1 (Screening) and Falls Part 2 (Risk Assessment and Plan of Care)

FAQ ID:89066

It is recommended that MLTSS plans report both rates. However, if the state believes there are valid reasons for not reporting both rates, such as costly changes in assessment and care planning forms and information technology systems, it might consider phasing in the supplemental rates over time. For instance, in the first year of measure use (for example, measurement year 2018), the state could require MLTSS plans to report just the core rate, and then require that MLTSS plans report both core and supplemental rates for measurement year 2019 or 2020. Although they are called "supplemental rates," they are still very important, and should be viewed as "aspirational." MLTSS plans should strive to cover more assessment and care plan elements over time.

FAQ ID:89071

Value sets are the complete set of procedure and diagnostic codes used to identify a service or condition included in a measure. One of the assessment and care planning measures—LTSS Reassessment/Care Plan Update after Inpatient Discharge—uses value sets to identify potentially planned hospitalizations. Please see "Do I need to use value sets to calculate these measures? If so, where can I find the value sets?" for more information regarding using value sets for the three institutional rebalancing and utilization measures.

View the value sets (XLSX, 2.88 MB). Please see Table 2 in the "LTSS Value Sets to Codes" tab. Table 1 in the "LTSS Measures to Value Sets" tab shows each value set needed for each measure.

FAQ ID:89076

Yes, the same sample can be used for Part 1 of the Screening, Risk Assessment, and Plan of Care to Prevent Future Falls measure as the LTSS Comprehensive Assessment and Update, LTSS Comprehensive Care Plan and Update, and LTSS Shared Care Plan with Primary Care Practitioner measures.

FAQ ID:89081

In accordance with Medicare cost reporting, the state must use 12 months of cost data reported by each facility. With regard to payment data, the state should use actual amounts, to the extent available, then calculate a claims completion factor based on historic utilization. The state’s UPL submission must include an explanation of its methodology to estimate payments. The use of a claims completion factor provides a reasonable estimate of the amount that Medicare would pay for these services, consistent with the UPL as defined at 42 CFR 447.272.

FAQ ID:92446

Effective state fiscal year 2020, each state must submit a complete data set of payments to Medicaid providers, including providers paid at cost, as well as critical access hospitals. This would require states to submit cost and payment data to CMS that previously was not requested.

FAQ ID:92456

Annually, CMS will request a list of covered durable medical equipment HCPCS codes from the Medicare Pricing, Data Analysis and Coding Contractor. Once the list is received, CMS will distribute the list through the CMS Regional Office Associate Regional Administrator.

FAQ ID:93671

To address claims run-out and ensure compliance with the FFP limit, we recommend states with these concerns conduct interim FFP limit demonstrations for DME no later than three months after the end of the calendar year for the previous calendar year (that is, January 1-December 31). The interim DME FFP limit demonstration will be due by March 31 of each calendar year and will contain data for the period of January 1 to December 31 of the preceding year. The final demonstration would be due one year later on March 31 and include all claims received during the run-out period dates of service within the interim demonstration period. The interim demonstration process should provide states with an understanding of potential violations of the FFP to make any necessary budgeting and rate changes. This method is being used to allow provide for a reasonable claims run out period as allowed under 42 CFR 424.44, which states that claims must be filed no later than one calendar year after the date of service.

FAQ ID:93676

The Precertification Pilot was an experiment conducted from October 2017-March 2018 designed to streamline certification and attract new vendors. Unfortunately, the pilot was found to be unscalable across Medicaid. However, key learnings from the pilot will be incorporated into current processes and future experiments around vendor engagement, certification, scalability, and sustainability. The goals the Centers from Medicare & Medicaid Services (CMS) identified at the beginning of the Precertification Pilot process remain the same: reduce the level of effort of certification; shorten the certification timeline; promote modularity and interoperability; reduce risk of system failure; and attract new vendors to the Medicaid IT market. Contact CMS with your ideas for experiments to achieve those goals at MES@cms.hhs.gov.

FAQ ID:95151